RocketFish RF-RBWSO2 User Manual download pdf

If this is your rst Rocketboost product and you do not have an existing Rocketboost

network, the devices were joined at the factory. You do not need to join them.

If you

are

adding these devices to an existing network, change the hub mode switch on the sender

to Disabled and then join BOTH devices to your existing hub.

Use this procedure only if you need to rejoin the transmitter and speaker. This procedure

is not required for normal operation as devices were joined at the factory. To connect

these devices to an existing hub device that you own, follow the same instructions: Join

the sender/receiver to your existing hub, then join the wireless speaker to your existing

hub. Note: You can only join devices to the hub unit (the one with the green LED).

Rocketboost device

A Set the HUB STATUS switch to ENABLE if this is your rst Rocketboost product set.

• The LED lights green when the HUB STATUS switch is set to ENABLE.

• The LED lights blue when the HUB STATUS switch is set to DISABLE.

B Press and hold the button on the sender/receiverfor more than three seconds to

put it into joining mode. The LED starts blinking rapidly and the unit will stay in Join

mode for 30 seconds.

C Press the Power/Join button on the wireless speaker for more than three seconds

so the sender and wireless speaker will enter connection mode.

• The LED lights steadily if the link is activated between both of the units.

• The LED blinks at a slower rate if the communication link is not successful.

D Once the link is established, if the Source LED on the wireless speaker is not

illuminated, press the Source button to toggle to the next source. If the LED is still

not illuminated, check that your source is powered up.

For further details, see instructions in the user manual for joining new devices to an

existing Rocketboost network.

RF-RBWSO2 Wireless Outdoor Speaker

QUICK SETUP GUIDE

Package contents

Sender

DC adapter

for transmitter

User Guide

IR remote

User Guide

Front controls

3.5mm stereo

female to 2-RCA male

cable (6 inches/15.25 cm)

Wireless speaker

DC adapter

for wireless

speaker

3.5 mm

stereo cable

Front Panel

Transmitter

Speaker

1 Getting Started

Connect to an audio source

Connect one end of the audio cable (supplied) to

the AUDIO IN jack on the sender and the other end

to the audio output jack of your device (such as an

A/V receiver, PC, or iPod.)

Note: If you are adding this sender to an existing network,

set the hub switch to Disable and follow the instructions

under Establishing Communication to add the transmitter

and speaker to your existing network. Otherwise, leave it

on Enable as the transmitter and wireless speaker were

pre-congured at the factory and you will not need to go

through the Establish Communication steps. Remember to

turn the volume up on the source device to at least 80%

of its maximum volume.

# Feature

Power/Join button

Power/Join indicator (Blue/Green Light)

IR sensor window

Source button

Receiver-mode indicator (Blue Light)

Sender-mode indicator (Blue Light)

To audio

output jack

Supplied

To audio

output jack

Supplied

Connect the AC Adapter

Connect one end of the adapter to the DC IN jack, then

plug the other end into an AC power outlet. The standby

indicator turns red.

Note: Make sure that the power outlet is 100-240V, and do not

connect the AC adapter until all other connections are completed.

Pull up the antennas

Adjust antennas

4 Listening to Music

To listen to music:

A Turn on the sender and the wireless speaker. Make sure that the wireless

speaker is fully charged (if using Batteries) and there is an active link

between the sender and the wireless speaker. An active link will be

indicated by the

Power LED showing a solid blue.

B Make sure the volume is turned up to about 80% of maximum volume.

C Adjust the volume level on your wireless speaker. If you have multiple

streams in your Rocketboost network, press the Source button on the

wireless speaker to hear the next stream.

Repeated pressing of the SOURCE button will toggle through available

sources.

ENGLISH 09-0536

Load batteries in wireless speaker

(Installing batteries is optional)

2 Connecting the Transmitter

A Unscrew the bottom cover ( 3 screws).

B Insert eight alkaline or rechargeable NiMH batteries

matching +/- as indicated. This product will only recharge

NiMH batteries. Do not attempt to charge any other

batteries in this product.

Note: Your wireless speaker can

operate on batteries or with the DC to AC adapter (provided).

The unit will charge and play simultaneously.

C Replace the cover and fasten the three screws.

x 8

8 rechargeable or alkaline

C batteries (not included)

Charge your wireless speaker

Connect the DC adapter to the wireless speaker and plug into an AC

power outlet. The CHARGE LED blinks green while it is charging. The

light will be solid when charging is complete.

Note: For the rst time,

charge batteries for

16 hours.

Caution: Only use the

supplied power adapter

and make sure your outlet

matches the AC’s input

of 100-240 V.

15V DC

BASS

Quick

Setup Guide

QUICK SETUP GUIDE

Wireless speaker

1 5

6 732

Preparing the remote control

To activate the battery:

Remove the tab from the bottom of the remote control to enable the battery.

Please read before setting up your system.

Every Rocketboost network must contain at least one hub device, which directs network data trac and helps devices join the

network. The network can have only one hub, which you can enable using the Hub switch on the back of all Rocketboost

transmitters. See your User Guide for instructions on “joining” devices to the network. If this is your rst Rocketboost product you

should make this unit the hub, if you already have Rocketboost products, you should disable the hub mode on this device.

IMPORTANT: Hub units must always have power for your network to operate. The device may be placed in standby, but the unit

must remain plugged into the wall to operate your network.

For best results, adjust the antennas to

vertical. In some instances, you may

improve range by rotating both

antennas 45 degrees to create a 90°

angle similar to a wide "V".

3 Establishing Communication

CHARGE

BASS

POWER/ /JOIN

CHANNEL

L - MONO - R

SOURCE

4 4

5 5

VOLVOL

Source

TX LED

Front Panel

Standby indicator (Red Light)

Volume increase/decrease dial

Power/on standby/Join button

Source

Middle-treble reflex hole

Bass reflex hole

Power/Join indicator (Red/Blue light)

BASS indicator

Charge indicator

Channel MONO (L/R) indicators

Audio source signal indicator

DC adaptor in

Bass Boost

# Feature

Wireless speaker’s

back panel

1 2

Summary of Contents

Page 1 - QUICK SETUP GUIDE

If this is your rst Rocketboost product and you do not have an existing Rocketboost network, the devices were joined at the factory. You do not need

Page 2 - LIVING ROOMLIVING ROOM

If this is your rst Rocketboost product and you do not have an existing Rocketboost network, the devices were joined at the factory. You do not need

Comments to this Manuals

No comments

RocketFish RF-RBWSO2 User Manual

Browse online or download User Manual for Portable speakers RocketFish RF-RBWSO2. Rocketfish RF-RBWSO2 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Portable speakers RocketFish RF-RBWSO2