RocketFish RF-RBKIT User's Guide download pdf

RF-RBKIT Wireless HD Audio Starter Kit

QUICK SETUP GUIDE

Initial setup

1 Unpack the package contents.

2 Enable the remote control battery.

Remove the tab from the bottom

of the remote control.

3 Set up the Wireless HD Audio Starter Kit.

The diagram shows a typical Wireless HD

Audio Starter Kit application for 5.1

home theater wireless surround

sound. For more information on

how to set this kit up for use with

a TV or MP3 player, additional

room audio, or a 7.1 home theater

setup, see your User Guide.

The wireless sender is connected

to the rear sound speaker outputs

of your home theater system and

the wireless receiver is connected

to the rear sound speakers.

See the following steps for further

setup details.

Package contents

Wireless sender

AC power adapter

(for wireless sender)

Remote control

3.5 mm to RCA adapters (2)

(6 inches/15.25 cm)

(for wireless sender)

Wireless receiver

AC power cable

(for wireless receiver)

3.5 mm stereo cables (2)

(for wireless sender)

Establishing communication

The wireless sender and wireless receiver packaged together with the Wireless HD Audio Starter Kit

were pre-paired so they will communicate with each other right out of the box. If you need to re-pair

the wireless sender and wireless receiver, use the following steps, otherwise you may skip this section

and go to, Using your wireless sender and receiver.

1 Set the HUB STATUS switch on the wireless sender to ENABLE if this is your rst Rocketboost

product set.

• The power indicator turns green when the HUB STATUS switch is set to ENABLE.

• The power indicator turns blue when the HUB STATUS switch is set to DISABLE.

2 Press and hold on the wireless sender for more than three seconds to put it into pairing mode.

The power indicator starts blinking rapidly and the unit will stay in pairing mode for 30 seconds.

3 Press and hold on the wireless receiver for more than three seconds so the wireless sender and

wireless receiver enter pairing mode.

• The power indicator lights steadily if pairing was successful.

• The power indicator blinks slowly if pairing was not successful.

If you already have other Rocketboost devices, you need to pair both the wireless sender and wireless

receiver to your existing hub device. See your User Guide for detailed instructions on how to do this.

Using your wireless sender and wireless receiver

1 Turn on the wireless sender and wireless receiver. The power indicator LEDs should light steadily. If

they are blinking, you need to rejoin the wireless sender and wireless receiver. See the Establishing

communication above.

2 Turn on the audio source connected to the wireless sender. Make sure the volume of the audio

source is not muted, otherwise no audio will be sent over the Rocketboost network.

3 Press the SOURCE A button on the wireless sender to turn on the source to the A input. The LED

around the source button turns on to show that the source is enabled.

4 Adjust the audio level on the wireless receiver.

Rocketboost network notes:

Every Rocketboost network must contain

one hub device, which helps devices join

the network. The network can have only

one hub, which you can enable using the

hub switch on the back of all Rocketboost

wireless senders and wireless

sender/receivers. If this is your rst

Rocketboost product, you should make this

device the hub, if you already have

Rocketboost products, you should disable

hub mode on this device.

Important: Hub devices must always have

power for your network to operate. The hub

device can be in standby (power-saving)

mode, but must stay plugged in.

ENGLISH 10-1332

Connecting the wireless sender

Note: If you already had your speakers connected to the back of your

home theater system, you will need to disconnect them before you

can set up your wireless sender and wireless receiver.

1 Connect the Right Surround speaker terminals of your

home theater system to the right speaker terminals of the

wireless sender on the Input A side. Use red speaker wire

to connect the red (+) terminals and black speaker wire to

connect the black (-) terminals. Repeat to connect the Left

Surround speaker terminals.

2 Plug one end of the AC power adapter into the wireless

sender and plug the other end of the cord into an AC

power outlet.

Connecting the wireless receiver

1 Connect the Right Surround speaker to the right speaker-out terminals on the wireless receiver.

Use a red speaker wire to connect the red (+) speaker-out terminal and black speaker wire to

connect the black (-) speaker-out terminal. Repeat to connect the Left Surround speaker.

2 Plug one end of the AC power cord to the AC IN jack on the back of the wireless receiver, then

plug the other end of the cord into into an AC power outlet. The Standby indicator turns on.

Cable spool

(for wireless receiver)

Speaker cable (4)

3 ft (91.5 cm)

User Guide Quick Setup Guide

Wireless sender

Wireless receiver

Home theater

system

SPEAKER-OUT (4-8 Ohm)

120V~,60Hz

AC IN

Left Surround speaker Right Surround speakerBack of wireless receiver

Home theater system

Note: Your home theater system may vary in appearance.

Refer to your home theater system manual.

Back of home theater system

Back of wireless sender

Left

Surround

Right

Surround

QUICK SETUP GUIDE 1

Summary of Contents

Page 1 - QUICK SETUP GUIDE

RF-RBKIT Wireless HD Audio Starter KitQUICK SETUP GUIDEInitial setup1 Unpack the package contents.2 Enable the remote control battery. Remove the t

Comments to this Manuals

No comments

RocketFish RF-RBKIT User's Guide

Browse online or download User's Guide for Unknown RocketFish RF-RBKIT. RocketFish RF-RBKIT User guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown RocketFish RF-RBKIT